Tile leveling system: how it works, benefits and what to watch out for
A tile leveling system keeps neighbouring tiles at the same height while you lay them, until the adhesive has set. This helps you avoid lippage, meaning edges where one tile sits higher than the other. Here you will learn how a leveling system works, when it is worthwhile and what to look out for when choosing and using one.
How does a leveling system work?
Common systems consist of two parts:
- Leveling tabs with a flat base that is slid under the edges of neighbouring tiles. The stem of the tab sticks up through the joint.
- A tensioning element placed on the tab from above: either a wedge (wedge system) or a cap screwed onto a thread (screw system).
The tensioning element pulls the tab upwards and presses the tile edges down evenly. Both tiles end up flush. Once the adhesive has cured, the tab stem is broken off at the predetermined breaking point and the tensioning element is removed. The base stays under the tiles and disappears when grouting. The thickness of the tab also sets the joint width.
Wedge or screw: the two types of system
- Wedge systems work with tabs and plastic wedges pushed sideways through the tab. Our Nivilli Keily is a wedge system.
- Screw systems work with threaded tabs and caps that are tightened by hand. Our Nivilli Spinny is a screw system: the caps are reusable, and the tabs are available for joint widths of 1 to 5 mm, for tile thicknesses of 3 to 15 mm indoors and 6 to 25 mm outdoors.
Which system suits your project is compared in detail in our guide Tile leveling system: wedge or screw?
When is a leveling system worthwhile?
- Large-format tiles: From about 60 × 60 cm and with long formats such as wood-look planks, small height differences are particularly noticeable. A leveling system is highly recommended here.
- Grazing light: At window fronts and with side lighting, every bit of lippage becomes visible.
- Thin joints: The narrower the joint, the more an offset stands out.
- DIYers: Even without much routine, a flat surface is easier to achieve because the system holds the edges while the adhesive sets.
For small formats on a very flat substrate, a leveling system is not essential, but it still helps to avoid lippage there too.
The advantages at a glance
- flat surface with less lippage and fewer trip edges
- even joints, because the tab sets the joint width
- less rework and less waste
- tiles are held against sinking and sliding while the adhesive sets
What to look out for
1. Choose the right tab
The tab must match the joint width and the tile thickness. With the Spinny, you can tell the joint width by the colour of the tab. Whether you need the indoor or outdoor tab depends on the thickness of your tiles.
2. Prepare the substrate
A leveling system compensates for height differences between neighbouring tiles, but not for an uneven substrate. The substrate must be clean, load-bearing and flat. Level larger unevenness beforehand, see Spreading levelling compound correctly.
3. Set tabs immediately
Tabs and tensioning elements belong on the tile right as you lay it, not after a few rows. Tiles can only be aligned while the adhesive is fresh. Our consumption calculator works out how many tabs you need.
4. Tension evenly
Tighten until the tiles are flush, but not with force. Overtightening can make the tab tear off prematurely.
5. Remove correctly
Only remove the system once the adhesive has cured according to the manufacturer. With the Spinny, knock off the tab together with the cap at the predetermined breaking point, in the direction of the joint, never across it, otherwise the tile edges can be damaged. Then unscrew the cap from the stem and reuse it.
6. Work cleanly
Remove adhesive residue from tabs and caps before it cures. Clean reusable caps after the job so they are ready for the next project.
Common mistakes
- wrong tab size for the tile thickness
- tabs set too late, after the adhesive has started to set
- using a leveling system as a substitute for a flat substrate
- knocking off the tab stem across the joint
- removing caps or wedges too early
Frequently asked questions
What is a tile leveling system?
A tool made of leveling tabs and wedges or caps that pulls neighbouring tiles to the same height while laying and holds them there until the adhesive has set. This helps to avoid lippage.
Is a leveling system worthwhile for DIYers?
For large-format tiles, yes. The larger the tile, the harder it is to lay it perfectly flush by hand. For small formats on a flat substrate, it is not strictly necessary.
Can leveling systems be reused?
The tabs stay in the joint and are consumables. Depending on the system, the tensioning elements are reusable: with the Nivilli Spinny, you use the caps again and again and usually only reorder leveling tabs.
Which leveling system is the best?
That depends on the project and the way you work. You will find a detailed comparison in our guide Wedge or screw.