Fliesen verlegen – So gelingt dein Projekt

Laying tiles: a step-by-step guide

Bathroom, kitchen or hallway: laying tiles yourself is no rocket science if preparation, tools and order are right. In this guide we go through tiling step by step, from the substrate to the finished joint. You will also learn which type of tile suits which area and what matters with joints.

What you need

Tools

  • Tile cutter and, for cut-outs, an angle grinder with a diamond cutting disc
  • Notched trowel, smoothing trowel, mixer and mortar bucket
  • Spirit level, straightedge, folding rule and pencil
  • Rubber mallet
  • Tile spacers and, for large formats, a tile leveling system
  • Grout float or rubber float, sponge float and bucket

You will find a detailed list in our guide Tiling tools: the basic kit for tilers.

Materials

  • Tiles with a reserve for offcuts. As a rule of thumb, about 10 % extra; more for diagonal layouts or many cut-outs.
  • Tile adhesive suited to the tile and substrate
  • Primer, depending on the substrate
  • Grout
  • Silicone for connection and movement joints
  • In the bathroom: waterproofing for wet areas

Step 1: Check and prepare the substrate

The substrate must be flat, clean, dry and load-bearing. Check flatness with the straightedge before you start.

  • Remove old, loose coverings and adhesive residue.
  • Level larger unevenness beforehand with levelling compound. How to do this is explained in our guide Spreading levelling compound correctly.
  • Prime absorbent substrates according to the manufacturer's instructions.
  • Waterproof showers and other wet areas before tiling, using a matched waterproofing system from one manufacturer: liquid membrane, sealing tape in corners and at transitions, and collars at pipe penetrations and drains. Layer thickness and drying time according to the manufacturer.

The flatter the substrate, the less you have to compensate with the adhesive bed later.

Step 2: Choose the right tile

Not every tile fits everywhere. The main types at a glance:

Tile type Properties Typical use
Earthenware Easy to cut, absorbs more water, usually not frost-resistant Indoor wall tiles
Stoneware Denser and more durable than earthenware Floors and walls, outdoors depending on the product
Porcelain stoneware Very dense and hard, absorbs hardly any water, often frost-resistant Floors, large formats, outdoors depending on the product
Natural stone Every slab is unique, more sensitive depending on the stone Floors, walls, outdoor areas depending on the stone
Glass and mosaic tiles Decorative, small-format Accents in bathrooms and kitchens

For floors in bathrooms, showers and outdoors, pay attention to the right slip resistance. Outdoors, only use tiles that the manufacturer explicitly declares frost-resistant. For natural stone and porcelain stoneware, the manufacturer often specifies a particular adhesive. Stick to it.

Step 3: Plan the layout

  • Find the centre of the room and mark a straight reference line with a chalk line or line laser.
  • Choose the pattern: straight, offset or diagonal. For large-format tiles, choose the offset according to the manufacturer, often no more than one third.
  • Lay the tiles out dry and check the edge pieces.

Goal: edge tiles on opposite sides should be as equal in width as possible, and narrow leftover strips should be avoided altogether.

Step 4: Mix and apply the adhesive

  • Mix the adhesive lump-free with the mixer according to the manufacturer's instructions and let it mature briefly.
  • Apply a thin contact layer with the smooth side of the notched trowel, then comb it evenly with the notched side.
  • Only spread as much area as you can cover within the adhesive's open time. It is stated on the packaging.
  • For large formats and outdoors, also butter the back of the tile thinly. This combined method is called buttering-floating and gives a more complete bed.

The right notch size depends on the tile format and the substrate. Larger tiles usually need a larger notch.

Step 5: Set and align the tiles

  • Place the tile, slide it in slightly and press it down. Tap with the rubber mallet if needed.
  • Keep joints even with tile spacers.
  • Check continuously with the spirit level.
  • With large-format tiles, a tile leveling system helps to avoid lippage. With the Nivilli Spinny, the leveling tab also sets the joint width; tabs are available for 1 to 5 mm. Which system suits you is explained in our guide Wedge or screw.

For cuts and cut-outs, see Cutting tiles: methods, tools and tips.

Step 6: Let it cure

How long the adhesive needs before you can walk on the surface and grout it depends on the product, the temperature and the layer thickness. Rapid-setting adhesives are often ready after a few hours, standard adhesives after about a day. The information on the packaging is decisive. Then remove the leveling aids and scrape adhesive residue out of the joints. It is best to pull out spacers earlier, while the adhesive is not yet fully set.

Step 7: Grouting

Joints are more than looks. They compensate for small dimensional tolerances of the tiles, protect the edges and seal the surface.

The right grout

  • Cementitious grout: the standard for most wall and floor surfaces, easy to work with.
  • Epoxy grout: very resistant and easy to clean, for example for kitchens and heavily used areas. It is more demanding to apply. Epoxy can cause allergies on skin contact, so always wear gloves and follow the manufacturer's instructions.
  • Silicone: for corners, connections to bathtub, shower and wall, and for movement joints. These joints must be elastic and are not filled with grout. Silicone joints are maintenance joints: check them regularly and renew them if they crack or come loose.

How to proceed

  1. Mix the grout according to the manufacturer's instructions.
  2. Work it in diagonally to the joint with a grout float or rubber float until the joints are full and compacted.
  3. After the specified waiting time, wash off diagonally with a damp sponge float without pulling material out of the joints.
  4. Once dry, polish off the cement haze with a dry cloth.
  5. Finally, apply the silicone joints.

Light joints make surfaces look calmer; darker joints are easier to care for in everyday life.

Common mistakes

  • Laying on an uneven or dusty substrate
  • Spreading too much adhesive so that it skins over before the tile is placed
  • Narrow edge strips because the tiles were not laid out dry
  • Filling corners and connections with grout instead of silicone
  • Grouting or loading the surface too early

Frequently asked questions

Can I lay tiles myself as a beginner?

Yes, with good preparation and some patience. Medium formats on a flat substrate are suitable for getting started. Walk-in showers, waterproofing and very large formats are more demanding. Here, support from a professional is worthwhile.

Where do I start tiling?

On floors, usually in the centre of the room at a reference line or at the most visible edge, not simply in a corner. This keeps the edge pieces even. On walls, you often start with the second row on a screwed-on batten and set the bottom row last.

How wide should the joints be?

That depends on the tile format, the dimensional accuracy of the tile and the manufacturer's instructions. On indoor walls, narrow joints of about 1.5 to 3 mm are common; on floors and with larger tolerances, correspondingly wider ones.

Back to blog